Learn / Start here · guide 1 of 10

Start here: the board and its documents

You know what is on the board, which of the seven PDFs answers which question, and how to go from "I want to use X" to the right register.

Beginner≈ 20 min

Before writing code, learn to find things. This guide tours the board, explains what each document is for, and walks the lookup chain you will use in every other guide: user manual → schematic → datasheet → reference manual.

You will learn
You need
  • The board and a micro-USB cable
1

Meet the board

The STM32H750B-DK is a Discovery kit built around an STM32H750XBH6 microcontroller: an Arm Cortex-M7 at up to 480 MHz with 1 MB of RAM. Around it sit a 4.3" touch screen, 8 MB of usable SDRAM, 2 × 64 MB of Quad-SPI flash, audio, Ethernet, USB, CAN, an Arduino header and an STMod+ header.

Plug a USB cable into CN14, the ST-LINK connector. That one cable powers the board, flashes your programs, lets you debug, and gives you a serial port to the PC.

2

One chip, two kinds of manuals

ST splits the chip documentation in two:

  • The datasheet describes this exact part: which peripherals it has, which pin can do what, voltage and current limits. Open it to choose pins.
  • The reference manual describes how the peripherals work and every register bit. It covers several sibling chips (H742/H743/H753/H750), so a few things in it are not present on every package. Open it to write code.

The CPU core itself (interrupts, SysTick, caches, the MPU) is Arm’s design and lives in the programming manual.

Tip. The documents page explains every PDF and lists questions each one answers.

3

Two manuals for the board

The user manual (UM2488) explains the board as a product: power, jumpers, connectors, and which on-board chip uses which MCU peripheral. It is short; skim all of chapter 6 once.

The schematic (MB1381) is the circuit itself. Sheet 3 shows the MCU with every ball and the net it drives. When the user manual and the schematic disagree, the schematic wins.

4

The lookup chain

Almost every "how do I use X" question follows the same path. Example: you want to print text to your PC.

  1. User manual: the virtual COM port is USART3.
  2. Schematic: nets VCP_TX and VCP_RX leave the MCU on PB10 and PB11.
  3. Datasheet: in the alternate-function table, PB10 carries USART3_TX as AF7.
  4. Reference manual: the USART chapter explains baud rate and the registers to write.
  5. Programming manual: only if you need the interrupt side (NVIC, priorities).

Try it now: search PB10 on the home page. The pin card shows the board net, all alternate functions with their AF numbers, and links to every page above.

5

How to read a reference manual chapter

Every peripheral chapter has the same order: introduction, main features, functional description, interrupts, registers, register map. Don’t start at the registers.

  • Read the introduction and main features (two pages) to know what the block can do.
  • Read only the part of the functional description you need.
  • Use the register description as a dictionary: look up a bit when your code needs it.
  • Check the reset value of each register you touch. It tells you what is already set up for you.

The GPIO chapter is short and is the best first one to read.

6

Set up the tools

Install STM32CubeIDE (free, Windows/macOS/Linux). Create a project with the board selector and choose STM32H750B-DK: it generates startup code, clock setup and HAL calls.

The guides show both styles: HAL calls, and the raw register writes they boil down to (using the CMSIS header). Write HAL to get something working, then read the register version next to it. That is how the manuals start making sense.

Tip. The H750 is a "value line" part: 128 KB of internal flash. Small programs fit easily. Large ones (graphics, audio) run from the external Quad-SPI flash; see the memory guide.

Common mistakes

  • Reading the reference manual front to back. It is a dictionary: open the chapter for the peripheral you are using.
  • Trusting a pin from a tutorial for a different board. Always confirm on this board’s schematic what the pin is already wired to.

Check yourself

Try to answer before opening. If you get stuck, the pages linked above have the answer.

You want to know the maximum current one GPIO pin can source. Which document?

The datasheet, electrical characteristics chapter. Limits are part-specific, so they are never in the reference manual.

You want to know what bit 3 of USART_CR1 does. Which document?

The reference manual, USART chapter, register descriptions.

Which pin drives the LCD backlight enable?

Search LCD_BL: the schematic net leaves the MCU on PK0.

Reading list

Every page this guide sent you to, by document. Reading them in order is a good revision.

UM2488UM2488 STM32H745I/H750B-DK Discovery kit user manualp.2p.7p.8p.11p.15p.23
DS12556STM32H750xB datasheetp.17p.23p.80
PM0253PM0253 Cortex-M7 programming manualp.183
MB1381MB1381 Discovery board schematic (H750XB variant)sheet 3sheet 3
RM0433RM0433 reference manual (STM32H742/743/753/750)p.530p.540p.2021

Search next

Each of these opens the finder with pins, registers, schematic hits and document pages for the term.

Where to go next