Documentation map

ST splits the information about this board over five kinds of document. Each one answers a different kind of question, so knowing which to open saves a lot of searching.

Which document answers my question?

I want to know…OpenTry searching
Which pin can do function X (UART, SPI, timer channel…)?DatasheetUSART1_TX
What is pin X connected to on the board?SchematicsPJ2
What does register bit Y mean / reset value?Reference manualRCC_AHB4ENR
How do I set up the clock tree / PLL?Reference manualPLL configuration
Interrupt priorities, MPU, caches, fault handlingProgramming manualMPU
How do I power or configure the board (jumpers, solder bridges)?User manual (board)solder bridge
Electrical limits: voltage, current, timingDatasheetabsolute maximum ratings
Which pins are on the Arduino / STMod+ headers?SchematicsARD_D
DS

Datasheet

What this exact chip is: pins, limits, packages.

Written for one part number family (STM32H750xB). It lists which peripherals exist on this die, how many, which pin can carry which signal (alternate-function tables), and the electrical limits: supply ranges, current draw, I/O levels, clock and ADC characteristics, timing. It does not explain how to program anything.

Use it when
  • Which pins can be USART1_TX, and with which AF number?
  • What ball is PA9 on the TFBGA240 package?
  • Is a pin 5 V tolerant (FT) or analog-only (TT/ANA)?
  • Max GPIO current, VDD range, HSE crystal limits, ADC sampling rate.

Not for: Register bits and peripheral behaviour: that is the reference manual.

Jump to
DS12556337 pages

STM32H750xB datasheet

Pinout, alternate functions, electrical characteristics, package data for the STM32H750VB/ZB/IB/XB.

RM

Reference manual

How every peripheral works, down to each register bit.

One manual covers several chips of the line (H742, H743/753, H750), so some chapters describe peripherals the H750 may not have in every package. Every peripheral chapter has the same shape: introduction, main features, functional description, interrupts, then the register descriptions with bit fields, reset values and a register map. This is the document you live in while writing drivers.

Use it when
  • What does RCC_AHB4ENR bit 0 do? What is the reset value?
  • How do I configure DMA streams and DMAMUX request IDs?
  • Clock tree, PLL configuration and kernel clock muxes (RCC chapter).
  • Base address of a peripheral (memory map section of the RM).

Not for: Pin assignments for your package and electrical limits: that is the datasheet.

Jump to
RM04333353 pages

RM0433 reference manual (STM32H742/743/753/750)

How every peripheral works and every register bit: RCC, GPIO, DMA, timers, USART, SPI, FMC, LTDC…

PM

Programming manual

The Arm Cortex-M7 core itself, shared by all STM32F7 and H7 parts.

Covers what is inside the CPU rather than the ST peripherals: programmer’s model and registers, the Thumb instruction set, exception model and priorities, and the core peripherals that sit on the private bus (NVIC, SCB, SysTick, MPU, FPU, L1 caches). Read it for anything that is the same on every Cortex-M7.

Use it when
  • How do exception priorities and preemption work?
  • MPU region setup, cache maintenance (SCB_CleanDCache), memory barriers.
  • What does an instruction like LDREX or VLDR do and how many cycles?
  • SysTick, SCB->VTOR, fault status registers (CFSR, HFSR).

Not for: Anything outside the core (GPIO, RCC, timers…): that is the reference manual.

Jump to
PM0253254 pages

PM0253 Cortex-M7 programming manual

The Cortex-M7 core: instruction set, exceptions, NVIC, SCB, SysTick, MPU, FPU, caches.

UM

User manual (board)

The Discovery kit and STMod+ board as hardware you hold in your hand.

Describes the boards rather than the chip: how to power them, the ST-LINK/V3E debugger and virtual COM port, jumper and solder-bridge settings, every connector pinout (Arduino, STMod+, audio, Ethernet), and which on-board device sits on which MCU signals. The STMod+ fan-out manual explains how the STMod+ connector breaks out to Grove, mikroBUS and other headers.

Use it when
  • Which UART is the ST-LINK virtual COM port?
  • What does solder bridge SBxx change? Which jumper selects the power source?
  • Arduino connector pinout and which MCU pin each header pin maps to.
  • How the LCD, SDRAM, QSPI flash and audio codec are connected.

Not for: Exact wiring details (series resistors, pull-ups, which net goes where): use the schematic.

Jump to
UM248839 pages

UM2488 STM32H745I/H750B-DK Discovery kit user manual

The Discovery board: power options, jumpers, solder bridges, connectors, ST-LINK, on-board devices.

UM269512 pages

UM2695 STMod+ fan-out expansion board user manual

The STMod+ fan-out board (MB1280): Grove, mikroBUS, Pmod-style headers and how they map to STMod+.

SCH

Schematics

The ground truth of the board: every part, net and pin.

The circuit diagrams of the Discovery board (MB1381, H750XB variant) and the STMod+ fan-out board (MB1280). Sheet 3 shows the MCU with every ball and the net it drives. Follow a net label (for example ARD_D1 or STMOD#2-TX) to its other sheets to see where a signal really goes, which series resistors, pull-ups or solder bridges sit on it, and whether a pin is free.

Use it when
  • Which MCU pin drives LED1, the LCD backlight or the user button?
  • Is PB7 already used on this board, or free for my project?
  • Which components sit between a pin and the connector?
  • Power tree: regulators, SMPS/LDO configuration, decoupling.

Not for: Why a peripheral behaves the way it does: go back to the reference manual.

Jump to
MB138122 pages

MB1381 Discovery board schematic (H750XB variant)

Every net on the STM32H750B-DK: MCU pins, SDRAM, QSPI, LCD, Ethernet, audio, Arduino, STMod+, ST-LINK.

MB12807 pages

MB1280 STMod+ fan-out board schematic

Schematic of the STMod+ fan-out board: STMod+ connector to Grove, mikroBUS and extension headers.

This set covers the five documents above plus the two schematics. The errata sheet and ST application notes are not part of it; check st.com for those.